How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
What are your thoughts concerning How to Install a Bathtub Yourself?
Mounting a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately tough project. If the old bathtub is easily accessible, the task can move speedily; if you need to open up a wall to get rid of the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make certain you have qualified on your own for the job and also fit attempting it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to take into consideration using one before you begin. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly assist you mount a new bathtub in your shower room if you have currently bought a brand-new tub as well as don't require to change the plan of your previous water supply pipelines.
Your devices as well as product checklist need to make up the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is separate the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly problematic because of the limited access that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location in between the tap as well as the sink. Protect the faucet in position with the maker supplied backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former type should be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bath tub till the spirit level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the water supply and also inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has actually been used at the very least when as this will resolve it into its last setting.
Preparing for the Installment
Firstly, the sustaining framework provided with the bathroom should be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to stop stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, causing difficulties with wetness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealer can fracture rather very early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the market. It is suggested to fit the floor tiles making use of water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
As a fervent person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that excerpt was a smart idea. If you please take the time to distribute this page if you liked it. Thanks for taking the time to read it.
This Post
Report this page